壁挂炉进水管
DN10 DN13 DN15 DN16
SERIES:
壁挂炉进水管
DESCRIPTION:
DN10 DN13 DN15 DN16
CODE:
-
APPLICATION:
HVAC
LENGTH(mm):
300
350
400
450
500
550
600
COLLECT
DESCRIPTION
Q&A
COMMENTS

EPDM-DN8-HG_01.jpgEPDM-DN8-HG_02.jpgEPDM-DN8-HG_03.jpg

EPDM-DN8-HG_04.jpgEPDM-DN8-HG_06.jpgEPDM-DN8-HG_07.jpgEPDM-DN8-HG_09.jpg

en-P37,38-EPDM-DN8-HG_05.jpg

Q1
How much water pressure does the use of faucet fall just be water pressure high?
The tap water pressure is generally 3-5 kg, that is 0.3-0.5MPa or so. If more than 6 kilograms of pressure is relatively high, people will feel uncomfortable when using the faucet normally; Under 3 kilograms, generally think that water pressure is lower.
Q2
The faucet is leaking. What should I do?
Most people think that the faucet leakage is a problem with the spool. In fact, as long as it is properly used, the spool is not easy to go wrong. Therefore, if the faucet leaks, it should be analyzed from its essence.
A. The faucet still water after the spool is closed. The solution is to remove the handle and the decorative cover and tighten the pressure cap again. There may be another possibility that the apron at the bottom of the spool is deformed and unable to seal the water. The solution is to remove the spool, check the bottom apron and reset it after re-installation.
B. Water oozes from around the spool. This phenomenon may be the spool loosening or displacement, the solution is to remove the spool to re-install
C, water oozing from the middle part of the spool. This phenomenon is damage to the spool, the solution is to replace the spool, if the faucet is leaking, replace the spool, which must increase the maintenance cost.
D. Leakage at the bottom of faucet. This phenomenon is generally caused by the O-ring of the intake pipe is not installed or deformed. The solution is to spin out the hose. If the O-ring is found to be not deformed, the O-ring and the intake pipe can be installed again.
Q3
What happened to the malfunctioning transfer switch of the bathtub faucet?
First, it may be the water pressure. If the water pressure is too small, the transfer switch may not bounce up. If the water pressure is too large, the transfer switch may not be pressed down. Second, there may be impurities stuck switch, can remove the switch cleaning.
Q4
How does faucet, flower asperse disorderly shoot water to return a responsibility?
This is because impurity clog filter place is caused, need to remove filter net only clean after impurity installation can be solved.
Q5
How to solve the faucet installation is not straight?
In the process of installation, you should first faucet in the case of not winding raw material belt and inside the joint on the silk, see whether the inside of the street silk whether there is a problem, found that the faucet is installed straight, unload its rewinding raw material belt, can not be greedy, after winding with the hand to take compaction raw material smoothing, on can be.
Q6
Wash basin faucet gives water very slow, faucet gives water smaller and smaller, how to solve?
A.first look at the adjacent other tap water is also very small, if it is also very small, is the problem of tap water pressure. Water pressure is insufficient. It is suggested to add an electric water pump.
B. If the channel is blocked or the bubbler is blocked and there is rust or impurities, the valve core can be removed and the channel is flushed again; If the bubbler is only clogged, remove the bubbler and clean it again.
C. slow water may be blocked sewer, use dredge agent or use physical negative pressure dredge; It is also possible that the sewer is too thin and does not match.
QUOTATION INQUIRY
*Product code
*Product LENGTH
*Your name
*Your job title
*Contact email
*Phone
*Area
*Consulting details